Leak detection and repairs across Cardiff and South Wales
A damp patch on the ceiling, water staining the wall, a meter that keeps spinning or a puddle under the kitchen. Cardiff Plumbing Limited finds the leak, traces it to the source and repairs it properly so it doesn't come back.
- We locate the leak, don't guess
- Minimal damage, maximum care
- Repair or replace, we advise
Seven ways water tells you something's wrong
Leaks hide. Most start small — a damp patch you notice when the light's right, a smell you can't place, a stain that slowly grows. By the time you see real water damage, the leak has been running for weeks. These are the warning signs we find most often.
Damp patches on ceilings or walls
Water finds its way down through plaster and joists long before you see the source. A yellow or brown stain is old water damage; a wet patch means the leak is active now.
Soft or spongy flooring or floorboards
Water trapped under or in the floor rots the timber and softens the finish. It often means a leak in the pipes below, or seeping up from the ground.
Your water meter keeps turning even when nothing's on
The meter only spins when water is running. If it's moving with all taps off and no toilet filling, water is leaking somewhere in the pipes or inside the walls.
A musty, damp smell you can't locate
Stale water in the walls, under floors or in cavities develops a distinctive smell long before visible mould appears. If your nose catches it in one room, the leak is usually behind that wall.
Mould or discolouration spreading on walls or ceilings
Mould grows where moisture sits. Black spots or patches that keep coming back after cleaning mean water is feeding them from behind the surface.
Your water bills have climbed for no reason
A hidden leak running 24 hours a day adds real money to the bill. If your usage is up without explanation, the pipes are likely leaking somewhere unseen.
Water pooling under or around radiators or pipes
Leaks at joints and connections often show up as a wet carpet or a puddle under a radiator, or along a pipe run. Act quickly — the longer water sits, the more structural damage spreads.
A slow leak costs water and money every day. More importantly, it rots timber, corrodes metal and encourages mould that damages health. The sooner you find and fix it, the less you'll spend on repairs and remedial work later.
Common leak sources and what we look for
Most leaks come from pipes or joints that are out of sight — under floors, in walls, behind units or above ceilings. We know where to look and how to trace water back to where it started.
- Corroded copper pipework
- Copper pipes corrode from the inside out, especially where water is slightly acidic or where the pipe has been damaged. Pinhole leaks develop slowly and are hard to spot until the wall stains.
- Leaking joints and connections
- Compression fittings, solder joints and push-fit connectors all fail in time. Movement, vibration, or just age weakens the seal and water seeps out at the joint.
- Burst or split pipes
- Freezing weather, ground movement, or damage during building work splits pipes. The leak may be steady or only happen when pressure rises — during the morning rush or when the heating fires up.
- Leaking heating cylinder or immersion heater
- An unvented cylinder or the immersion heater pocket develops a pinhole and water weeps out inside the tank or around the base.
- Leaking radiator or valve
- Radiators rust from the inside; valves wear. Water seeps from a small hole in the radiator body or from a corroded thermostatic valve.
- Water supply to outside taps or garden hose points
- These are often forgotten during winter. If not drained and isolated, they freeze and burst, leaking into the foundation or through the external wall.
- Leaking appliance connections
- Washing machines, dishwashers and cold-fill taps have inlet hoses that perish or connections that work loose. Water pools behind units or under floors.
- Roof leaks finding their way into the pipework
- Not always a pipe leak. Sometimes water from a roof or gutter runs down and stains pipes or ceilings, or pools where pipes are routed.
How we find and repair a leak properly
- Visual inspection of the damp area and the pipes and fittings nearby
- Listening tests to hear running water inside walls or floors
- Meter checks to confirm water is leaking and measure how much
- Isolating sections of pipe to narrow down the fault to one run
- Tracing the pipe route under floors and in walls using maps or test points
- Opening access where needed to inspect joints and pipe condition
- A clear explanation of where the leak is and how to fix it
- Repair work: patching, replacing the damaged section, or fitting new pipe as needed
- Pressure testing the repair and checking the system holds
- Making good any access holes and tidying the area
We photograph the leak and the repair so you have a record of what was done. If the damage underneath needs specialist work — timber repair, drying out, structural assessment — we'll tell you and advise on the next step.
From the first call to a dry house
You ring and describe the problem
Tell us where the water damage is showing, how long it's been there and what you've noticed. We ask questions so we know what equipment to bring.
We inspect and trace
We look at the damp, listen for running water, check your meter and isolate sections of pipe to find exactly where the leak is coming from.
We explain and quote
Once we've found it, we show you the leak, explain what caused it, tell you how to fix it and give you a price in writing before we start.
We repair it properly
We isolate the water, remove the damaged pipe or fitting, fit new material, test under pressure and make sure the repair holds.
We make good and tidy up
We close any access holes neatly, wipe down and make sure the area is left clean. You get the reassurance that it's fixed.
Leaks and the law
The Water Supply (Water Fittings) Regulations 1999 require that all pipework is maintained in good condition and that leaks are repaired without unreasonable delay. If the leak is on the supply owned by you, you must fix it. If it's on the company's pipe before the meter, they're responsible — but you should still report it.
We use materials and methods that meet BS 6700 and BS EN 1057 for copper pipe, BS 2871 for older steel pipe, and BS 1212 for ball valves and control fittings. Any replacement work is done to current Building Regulations standards and tested to ensure it works.
If the leak has caused structural damage, we'll advise on specialist surveys and remedial drying before the house is fully watertight again.
Why leak repairs vary in price
- Finding the leakSome leaks are obvious. Others mean opening walls, ceilings or floors to trace the pipe — that takes skill and time.
- How accessible it isA leak under a kitchen unit takes longer than one in an open pipe run because we have to work carefully in a tight space.
- The scale of damagePatching a pinhole in one pipe is a small job. Replacing a long corroded section costs more and may mean redecorating.
- The material and locationRepairing copper pipe in a wall is different from replacing an immersion heater pocket. Each calls for different skills and materials.
- Making goodIf we've had to open walls or ceilings to find the leak, the cost includes cutting carefully and making the opening good again.
- Structural issuesDamp timber, mould remediation or subsidence caused by the leak may need specialist input, which we'll advise on separately.
Keeping your pipes sound and water bills normal
Monitor for a week
Keep an eye on the repair area. It's normal to see damp drying out slowly, but if water reappears, ring us — the repair is guaranteed.
Check your meter
Note the meter reading after the repair. If it's moving again with nothing running, there may be another leak nearby.
Allow time for drying
Wet walls and timber dry slowly, especially in cold or damp weather. A dehumidifier or open windows help speed the process.
Inspect the original site regularly
When pipes burst or corrode once, corrosion is often elsewhere on the same system. Keep an eye on that area and nearby fittings.
Drain outside pipes in autumn
Frozen pipes burst and leak. Before winter, turn off and drain the supply to garden taps, hose connections and outside soap bowls.
Know your isolation valves
Learn where the main stopcock and any section isolators are. Test them yearly so you can shut water off in an emergency.
If the leak has revealed other pipe problems
Pipework repairs
Corroded, split or stained pipe sections, removed and replaced with new copper or plastic pipe run neatly.
Find out more →Radiator valve replacement
Leaking radiators and thermostatic valves, isolated and replaced to keep your heating running and your bills down.
Find out more →Unvented cylinders
High-pressure hot water cylinders, serviced, repaired or replaced to keep the system working safely.
Find out more →Leak detection and repair questions, answered plainly
How long does it usually take to find a leak?
It depends on where the leak is. If it's on a visible pipe or joint, we can pinpoint it in minutes. If it's hidden in a wall or under a floor, we may need to listen to different sections, check your meter and isolate pipes to narrow it down — that can take 1–2 hours. We'll explain what we're doing as we go.
What if the leak is on the water company's pipe?
The supply pipe from the main to your meter is owned by the water company. If the leak is there, they're responsible for the repair and it's free. We can help identify it. Any leaks after your meter are your responsibility — we repair those.
Will you have to open the walls or ceiling?
Sometimes, yes. If we can't locate the leak from above or below, we may need to open a small section carefully to see the pipe. We'll explain why before we do it, keep the opening as small as possible, and make it good afterwards. The cost of making good is included in the repair quote.
How much does a leak detection visit cost?
We charge a call-out fee for the inspection and fault-finding. Once we've located the leak, we give you a separate quote for the repair. If you decide to go ahead with us, we'll credit the inspection fee against the repair cost.
Can a leak be repaired without replacing the whole pipe?
Often, yes. If the leak is at a joint or a small pinhole, we can patch it or fit a new coupling. If the pipe is badly corroded or has multiple pinholes, replacing that section is safer and longer-lasting than patching. We'll advise which is best for your situation.
What should I do while I'm waiting for the plumber to come?
Turn off the main stopcock if you're concerned about flood damage. Take photos of any damp or staining so we can see how it's progressing. If water is pooling or running, try to contain it with towels or a bucket. Don't panic — most leaks are slow. We'll be with you as soon as we can.
Found a leak? Let's find where it's coming from
A qualified plumber will inspect the area, trace the water to its source and give you a clear repair plan with a fixed price.
03300437479