Skip to content
Taps, mixers and outside taps

Tap replacement and repairs across Cardiff and South Wales

Dripping, stiff, leaking or just worn out? Cardiff Plumbing Limited repairs the tap if a repair will last, and replaces it properly if it won't. You get a clear price before we touch anything.

  • Repair or replace, we tell you which
  • Price agreed before work starts
  • Old taps taken away
Signs it's time

Six signs your tap needs attention

Most tap problems start small. A drip you can ignore this month becomes a worn seat, a stained basin or water creeping into the cabinet underneath. These are the ones we're called out for most.

A drip that won't stop

Usually a worn washer or a tired ceramic cartridge. If the seat inside the tap is scored, a new washer only buys you a few weeks.

Water around the handle or base

Perished O-rings and spindle seals let water escape where it shouldn't. It runs down into the worktop or vanity unit and rots the board.

A tap that wobbles or moves

A loose fixing under the sink or basin. Left alone it strains the pipe connections below and starts a slow leak.

Stiff, gritty or hard to shut off

Limescale or corrosion inside the tap. If you have to force it closed, the internals are on their way out.

Weak or spraying flow

A clogged aerator is an easy fix. If the flow is still poor after cleaning, the problem is in the tap body or the pipe feeding it.

Flaking finish or crusty joints

Pitted chrome and green or white crust at the joints mean the metal is corroding. A repair won't hold, so replacement is the sensible choice.

Repair or replace?

If the body is sound and the fault is a washer, cartridge or seal, we repair it and keep the cost down. If the tap is corroded, the finish has failed or parts are no longer made, we'll say so and show you why before you spend anything.

Choosing a tap

Tap types and what they're made of

The right tap depends on the holes in your basin, sink or bath, and on the water system behind it. Here's how the common types differ.

Pillar taps
Separate hot and cold taps, each on its own hole. Traditional, simple and easy to repair. They suit older basins and baths.
Mixer taps
One spout, two handles or a single lever. Hot and cold blend before the water leaves, so you get a comfortable temperature without scalding or freezing your hands.
Monobloc
A single-hole mixer, popular on modern basins and kitchen sinks. Tidy to clean around, but the basin needs the right hole size.
Kitchen swan-neck
A tall, swivelling spout for deep sinks. Pull-out versions need a flexible hose and a little extra room in the cupboard below.
Wall-mounted and bath fillers
Fixed to the wall or the bath rim. These need careful pipe positioning and a sound wall behind, so we check before we start.
Outside taps
Need backflow protection so garden water can't be drawn back into your drinking supply, and are best isolated before winter.

For the body, look for solid brass with a chrome, brushed nickel or black finish. Cheaper zinc-alloy bodies corrode sooner and are harder to repair. Ceramic disc cartridges outlast rubber washers and give a smooth quarter-turn action.

Check your water pressure first

Many mixer taps are designed for mains-pressure hot and cold. If your hot water comes from a tank in the loft, you need a tap made for low-pressure systems or it will trickle. Tell us how your hot water is supplied and we'll make sure the tap matches.

What's included

Everything that goes into a proper tap job

  • Checking the old tap and the pipes behind it before we quote
  • Isolating the water supply, so the rest of the house keeps running where possible
  • Fitting a small isolation valve under the tap if there isn't one
  • Removing the old tap, including seized or corroded fixings
  • New flexible tap connectors where the old ones are tired
  • Fitting the new tap, level and firmly fixed
  • Checking hot is on the hot side and cold is on the cold
  • Testing every joint under pressure and flushing out debris
  • Wiping down the basin or sink and taking the old tap away

Already chosen a tap? Tell us the make and model when you ring and we'll check it suits your system before you open the box.

How the job works

From the first call to a tap that works

  1. You call

    Tell us what the tap is doing and where it is. We'll ask the right questions so we arrive with the right parts.

  2. We find the fault

    We look at the tap and the pipework, explain whether to repair or replace and give you a clear price.

  3. We do the work

    Water off, old tap out, new tap or parts in. Fixings are tightened properly and the connections are tested.

  4. We tidy and check

    We clean up, take the old tap away and run the water so you can see it working before we go.

UK standards

Fitted to the water regulations

All taps and fittings must comply with the Water Supply (Water Fittings) Regulations 1999. They have to be a suitable, approved product, installed so they don't waste, misuse or contaminate the water supply.

In practice that means WRAS-approved or equivalent taps, correct backflow protection on outside and hose-connected taps, and joints made and tested properly. Look for taps made to BS EN 200, the European standard for sanitary tapware.

Taps on a kitchen sink should take their cold water from the mains. We'll check this on every kitchen job.

What affects the cost

Why one tap job costs more than another

  • Repair or replacementA new washer or cartridge costs far less than a new tap and fitting.
  • The tap itselfQuality, finish and type all change the price, from a basic pillar tap to a pull-out kitchen mixer.
  • Isolation valvesIf there's no working valve under the tap, we fit one so future repairs are quick.
  • AccessTight space behind a basin, a bath edge or a boxed-in sink takes longer to work in.
  • Condition of the old fittingsSeized nuts and corroded connectors can add time.
  • How many tapsDoing several in one visit usually saves on call-out time.
Aftercare

Keeping your new taps working for years

Clean them gently

Use a soft cloth and mild soapy water. Bleach and abrasive cleaners strip chrome and ruin black and brushed finishes.

Descale the aerator

Unscrew the spout end now and then and soak it in a limescale remover so the flow stays even.

Know your isolation valve

Find the small valve under the tap and give it a quarter turn each year, so you know it will shut off in an emergency.

Don't over-tighten

Turn the handle off until the water stops, then no further. Forcing it wears out the washer or cartridge sooner.

Act on drips early

A steady drip wastes water all year and marks the basin. It's a small job now and a bigger one later.

Protect outside taps

Turn off and drain the supply to outside taps before winter, and fit an insulated cover.

Questions answered

Tap replacement questions, answered plainly

Can a dripping tap be repaired, or does it need replacing?

Often it can be repaired. A worn washer, cartridge or seal is a quick fix if the tap body is in good condition. If the tap is corroded, the finish is flaking or the seat inside is damaged, a repair won't last and replacing it is better value. We'll tell you which applies before we start.

Can you fit a tap I've already bought?

Usually, yes. Give us the make and model when you ring. We'll check it suits your water pressure, your hot water system and the number of holes in your basin, sink or bath, so you don't find out it's wrong on the day.

Will a new mixer tap work with my hot water system?

It depends on how your hot water is supplied. Taps made for mains pressure can trickle on a low-pressure, tank-fed system, and the reverse can also be a problem. Tell us what you have and we'll make sure the tap matches the system.

Do you need to turn the water off to the whole house?

Not always. If there's an isolation valve under the tap, we use that and the rest of the house stays running. If there isn't one, we fit one as part of the job, so future repairs are simpler. It helps if you can show us where your stop tap is.

What affects the price of a tap replacement?

The type and quality of the tap, whether it's a repair or a full replacement, access behind the basin or sink, the condition of the old fittings and whether isolation valves need fitting. Cardiff Plumbing Limited gives you a clear price before any work begins.

Do outside taps need anything special?

Yes. An outside tap needs backflow protection, usually a double check valve, so water from a hosepipe can't flow back into your drinking supply. It's also worth isolating and draining it before winter to stop it freezing.

Got a tap that needs sorting?

A qualified, fully insured plumber will look at it, tell you what it needs and agree a price before starting.

03300437479